|
|
|
|
 more detail NEW Chrome Genuine Stromberg 97 carburetor Just in! The new Chrome Genuine Stromberg 97 carburetor that's chromed the traditional way. The high quality zinc alloy Genuine Stromberg 97 castings are hand polished. They're copper and nickel plated, buffed again then chromed before a finish detail polish to impart great color and depth. All of the stainless parts are hand polished before any sub-assemblies are completed. The brass S-jet inlet valve, idle needle screws and small plugs are chromed. And all of the threads and fuel passages are chased and cleaned before assembly. The base castings are supplied in the usual Stromberg high quality black lacquer finish. The final result is a real show quality chrome product with a full warranty. price: $599.95 |  more detail Black & Chrome Stromberg 97 Limited Edition! NEW! and in limited supply. Stromberg made a short run of Limited Edition black & chrome 97 carbs. The black on the body is the same catalyzed 2-pack used on Stromberg 97 bases. price: $475.95 |
 more detail NEW STROMBERG CARBURETOR - Genuine 97 - The REAL Brand new Stromberg 97!! Check out these features: - A new, improved early style cast iron base with stock size - not second-best oversize - throttle shaft, and the later Stromberg 1-1 style circuits built-in for improved off-idle response. - A new big 97 logo, Type 1 bowl casting, pressure-cast in new dies, CNC-machined for a blue-print parts fit with brand new emulsion tubes. -Stock Stromberg jetting 0.045" main jets and a Number 65 power valve. - A new air horn casting with extra meat around the float bowl lid to help prevent warping (and leaks). - A newly developed no-stick S-Jet inlet valve. - New brass fuel float. - Modern, high-tech, reinforced cellulose/nitrile gaskets. - Stainless steel instead of plated mild steel throughout. Stainless steel springs, accelerator pump rod, the throttle linkage, choke plate, lever and more. - Beautiful new investment cast stainless steel throttle and accelerator pump levers. price: $449.95 |  more detail STROMBERG CARBURETOR w/ Choke Cable Bracket - Genuine 97 - Here the real Brand new Stromberg 97 with the stainless steel choke cable bracket installed. price: $475.95 |
 more detail STROMBERG CARBURETOR w/ Lincoln Zephyr Throttle shaft - Genuine 97 - Here the real Brand new Stromberg 97 with the stainless steel Lincoln Zephyr Throttle shaft and lever kit installed. It's designed to push instead of pull the throttle lever. This is handy for cars like the 1949 Mercury or any 1930s Lincoln Zephyr where the pedal does exactly that. The throttle shaft is a replica of the original Lincoln Zephyr part. price: $449.95 |  more detail Genuine Stromberg 97 - Barn Find carburetor A brand new Genuine Stromberg 97 with factory patina! The more you handle them, the more patina they pick up. Available only from Stromberg Carburetor. Here are the highlights: Super-accurate pressure die-castings from new dies, CNC-machined for a blue-print parts fit. So no oversize screw threads. No mystery parts from previous rebuilds. No problems. An early style cast iron base with stock size - not second-best oversize - throttle shaft. Parkerized as per original factory spec. Lightly rusted on the outside, then rattle can painted with a careful mist of satin black. Main castings and stainless steel parts lightly media blasted. External brass parts heat aged. Every Barn Find model even comes with a 'Reconditioned with Stromberg Genuine Parts' rosette decal to complete the look. Operational efficiency remains key so some parts, like the choke plate, accelerator pump rod and springs, are left untouched. It all adds to the old, but reconditioned look. A reinforced air horn casting with extra material around the float bowl lid to eliminate warping and leaks. Stock original (sea level) Stromberg jetting - 0.045 main jets and a Number 65 power valve. 162cfm out of the box (independently verified) measured at 1.5inch Hg (same as they measure 4-bbl carbs). A new brass float, made in USA on original Stromberg dies. Our specially developed no-stick S-Jet inlet valve. Modern, high-tech, reinforced gaskets. Sorry, no leaks! Stainless steel linkage throughout. Our springs are stainless. So is the accelerator pump rod, the throttle linkage, choke plate, lever and more. Beautiful investment cast stainless steel throttle and accelerator pump levers. Original-style riveted throttle and choke shafts. Extensive dyno and road tests have proved that it matches or exceeds original spec. price: $475.95 |
 Original Stromberg 97-REBUILT Rebuilt large logo original Stromberg 97! Disassemble, including removal of emulsion tubes, chemical clean, beadblast, boil, ultrasonic clean and color bodies and airhorns using chromatic acid, leaving a grey-green-bronze coating that is impervious to fuel. Base is honed and fitted with new or excellent used plates and throttle shafts (.275") and new reamed bushings (.278"). All removable parts are checked and replaced with New Genuine Service parts as necessary. - Special extended knurled brass bleed screws for fat fingers - Add the POLISHED Stainless Steel kicker option below (Shown) - Standard .045 jets, .065 power valve - choice of jets and PVs at NO charge - No core or core charge!! |  more detail Ford Nut Compression Fittings You probably already know that a Ford Nut is the small brass compression fitting with the correct 1/2 x 20 UNF thread for Stromberg 97/81/48 inlet valves used with 1/4" OD hard fuel line. These come in handy packs of three complete with the brass ferrules. They fit the new Stromberg S-jet and original needle & seat. There's no need to flare the hard line end, just slip the Ford Nut over the end, add the ferrule on the end, then push the pipe firmly into the 97 inlet fitting and tighten the Ford Nut into it, compressing the ferrule to form a good fuel-tight joint. Ford Nuts also fit most Ford Flathead fuel pumps except the 1951-53 1BA glass bowl pump which uses 1/8" NPT fittings. price: $6.95 |
 more detail Ford Nut Compression Fittings CHROME Here's the same Ford Nut Compression Fittings describe above with beautiful CHROME plating. price: $15.95 |  more detail 1/4" Aluminum Fuel Line Here's a 10 ft. roll of 1/4" O.D. Aluminum Fuel Line to use with the Ford Nut compression fittings. 10 ft. roll rated to 250 psi. price: $14.95 |
 Inverted Flare Nuts Perfect for your multi-carb set up. Flare nuts are used for building custom length fuel lines. Choose zinc plated or Stainless Steel and size below. |  Hard Fuel Line Hard Fuel Line works great for building one piece custom fuel lines without unions. Stainless steel tubing is 304 grade and double annealed for easy flaring and bending. Choose zinc or Stainless and size below. Tubing does not include flare nuts (sold separately). |
 Aluminum Fuel Line Lightweight aluminum tubing replaces small diameter fuel lines used in most production automobiles. Made in USA. - Large diameter, .035" thick wall seamless tubing flows more fuel and eliminates fuel starvation - Legal in all classes; tested to 35 PSI, 25' coil, choose size below |  more detail TwoStep Fuel Line 2x2 - Flathead Ford & 11A pump Stainless steel fuel line for use on Offenhauser 1090 (1933-48 Ford Flathead) intake with 11A 'pepper pot' type fuel pump. Designed and manufactured exclusively by Stromberg Carburetor, TwoStep Fuel Lines combine super-clean looks with hot rod styling and simple installation. Each kit is supplied ready to install in just two simple steps. TwoStep kits are not a one size fits all solution. They're CAD engineered to fit Stromberg 97, 81, 48 and 40 carburetors on specific intake manifolds with specific fuel pumps (or a remote pump), so please check you're ordering the right kit. Carburetor spacing differs between intake makes and models and fuel pump mounts vary. Check out these features: - 1/4inch OD lines, CAD-designed and CNC-bent for an exact fit - Invisible furnace brazed joints for OE looks and fuel-tight quality - All stainless steel construction - Brass Ford Nut fittings are supplied - Fits Offenhauser 1090 intake manifold - Use with Ford 11A-9350 'pepper pot' fuel pump - Simple Two Step installation price: $100.95 |
 more detail TwoStep Fuel Line 2x2 - Flathead Ford & 59A pump Stainless steel fuel line for use on Offenhauser 1090 (1933-48 Ford Flathead) intake with 59A 'glass bowl' type fuel pump. Designed and manufactured exclusively by Stromberg Carburetor, TwoStep Fuel Lines combine super-clean looks with hot rod styling and simple installation. Each kit is supplied ready to install in just two simple steps. TwoStep kits are not a one size fits all solution. They're CAD engineered to fit Stromberg 97, 81, 48 and 40 carburetors on specific intake manifolds with specific fuel pumps (or a remote pump), so please check you're ordering the right kit. Carburetor spacing differs between intake makes and models and fuel pump mounts vary. Check out these features: - 1/4inch OD lines, CAD-designed and CNC-bent for an exact fit - Invisible furnace brazed joints for OE looks and fuel-tight quality - All stainless steel construction - Brass Ford Nut fittings are supplied - Fits Offenhauser 1090 intake manifold - Use with Ford 59A-9350 'glass bowl' fuel pump - Simple Two Step installation price: $100.95 |  more detail TwoStep Fuel Line 2x2 - Flathead Ford & 7RA pump Stainless steel fuel line for use on Offenhauser 1075 (1949-53 Ford Flathead) intake with 7RA '8BA engine' fuel pump and mount. Designed and manufactured exclusively by Stromberg Carburetor, TwoStep Fuel Lines combine super-clean looks with hot rod styling and simple installation. Each kit is supplied ready to install in just two simple steps. TwoStep kits are not a one size fits all solution. They're CAD engineered to fit Stromberg 97, 81, 48 and 40 carburetors on specific intake manifolds with specific fuel pumps (or a remote pump), so please check you're ordering the right kit. Carburetor spacing differs between intake makes and models and fuel pump mounts vary. This fuel line fits two carburetors on the Offenhauser 1075 intake (for 1949-53 Ford Flathead engines) with the stock Ford-type 7RA-9350 fuel pump. It DOES NOT fit the 1951-53 Ford 1BA-9350 fuel pump which requires 1/8in NPT fittings. Check out these features: - 1/4inch OD lines, CAD-designed and CNC-bent for an exact fit - Invisible furnace brazed joints for OE looks and fuel-tight quality - All stainless steel construction - Brass Ford Nut fittings are supplied - Fits Offenhauser 1075 (1949-53) intake manifold - Use with Ford 7RA-9350 fuel pump - Simple Two Step installation price: $100.95 |
 more detail TwoStep Fuel Line 3x2 - Flathead Ford & 11A pump Stainless steel fuel line for use on Edelbrock 1108 (1933-48 Ford Flathead) 3x2 intake with 11A 'pepper pot' type fuel pump. Designed and manufactured exclusively by Stromberg Carburetor, TwoStep Fuel Lines combine super-clean looks with hot rod styling and simple installation. Each kit is supplied ready to install in just two simple steps. TwoStep kits are not a one size fits all solution. They're CAD engineered to fit Stromberg 97, 81, 48 and 40 carburetors on specific intake manifolds with specific fuel pumps (or a remote pump), so please check you're ordering the right kit. Carburetor spacing differs between intake makes and models and fuel pump mounts vary. This fuel line fits three carburetors on the Edelbrock 1108 3x2 intake (for 1933-48 Ford Flathead engines) with the stock Ford-type 11A-9350 fuel pump - the 'pepper pot' shape pump without a glass bowl. Check out these features: - 1/4inch OD lines, CAD-designed and CNC-bent for an exact fit - Invisible furnace brazed joints for OE looks and fuel-tight quality - All stainless steel construction - Brass Ford Nut fittings are supplied - Fits Edelbrock 1108 3x2 intake manifold - Use only with Ford 11A-9350 'pepper pot' fuel pump - Simple Two Step installation price: $150.95 |  Stromberg banjo fitting NEW! When Stromberg makes a new banjo fitting, you've got to expect something different. Check out these special features: - Stainless Steel - Perfect proportions - made form large diameter material - Recess lips on each side hides the gaskets - No ugly crush washer spoiling your multi carb set up Sized to fit both 5/16" and 3/8" hose, with plenty of fuel flow guaranteed. Order today! |
 more detail Banjo fitting, Single, w/ fuel gauge fitting All the benefits of our super-popular double-end banjo fitting, but with an 1/8th NPT hole in the end of the banjo bolt to accept your hot rod fuel pressure gauge. All the more important with Stromberg 97 carburetors because you need to ensure 2.5psi max. Big diameter stainless steel material with a recess lip on each side to hide the gasket and move the bolt head closer to the banjo. The wrench surfaces are short, and we knocked the corners off the hex and rounded the bolt head too. They're sized to fit both 5/16inch and 3/8inch hose, with plenty of fuel flow guaranteed. - Media polished stainless steel banjo - 1/8th NPT threaded banjo bolt accepts fuel pressure gauge - Recess lip on each side hides the gasket - Sized to fit both 5/16inch and 3/8inch hose - Read fuel pressure at the carb! - Gauge not included! price: $31.95 |  more detail Banjo fitting, double, w/ fuel gauge fitting All the benefits of our super-popular double-end banjo fitting, but with an 1/8th NPT hole in the end of the banjo bolt to accept your hot rod fuel pressure gauge. All the more important with Stromberg 97 carburetors because you need to ensure 2.5psi max. Big diameter stainless steel material with a recess lip on each side to hide the gasket and move the bolt head closer to the banjo. The wrench surfaces are short, and we knocked the corners off the hex and rounded the bolt head too. They're sized to fit both 5/16inch and 3/8inch hose, with plenty of fuel flow guaranteed. - Media polished stainless steel banjo - 1/8th NPT threaded banjo bolt accepts fuel pressure gauge - Recess lip on each side hides the gasket - Sized to fit both 5/16inch and 3/8inch hose - Read fuel pressure at the carb! - Gauge not included! price: $35.95 |
 more detail Replacement banjo bolt - fits fuel gauge Do you already have some Stromberg banjo fuel fittings and now want to add a fuel pressure gauge? Well here's your answer! This is the BOLT ONLY and gaskets. - 1/8th NPT threaded banjo bolt accepts fuel pressure gauge price: $17.95 |  more detail Banjo fitting - single end. Polished The perfect hot rod banjo fitting. For great proportions, we make them from big diameter stainless steel material with a recess lip on each side to hide the gasket and move the bolt head closer to the banjo. We kept the wrench surfaces short, knocked the corners off the hex and rounded the bolt head too. They're sized to fit both 5/16inch and 3/8inch hose, with plenty of fuel flow guaranteed. - Fully, machine polished stainless steel banjo - Recess lip on each side hides the gasket - Sized to fit both 5/16 inch and 3/8 inch fuel hose - Works perfectly with 9083k - double end version price: $29.95 |
 more detail Banjo fitting - double end. Polished The same as our 9082K-P fully polished single banjos, but with hose on both sides. For perfect proportions, we make them from big diameter stainless steel material with a recess lip on each side to hide the gasket and move the bolt head closer to the banjo. We kept the wrench surfaces short, knocked the corners off the hex and rounded the bolt head too. They're sized to fit both 5/16inch and 3/8inch hose, with plenty of fuel flow guaranteed. - Fully, machine polished stainless steel banjo - Recess lip on each side hides the gasket - Sized to fit both 5/16inch and 3/8 inch fuel hose - Works perfectly with 9082k - single outlet version price: $33.95 |  more detail Stromberg Banjo Spacer The new Stromberg Banjo Fitting Spacer moves the banjo fuel line out one inch from the inlet fitting, providing instant clearance for the long centre lever arm you find on all tripower progressive linkages. The new, media polished, stainless steel banjo spacer uses our proven Stromberg superseat end, with its correct 18 degree seat, into the inlet fitting (original or Stromberg S-jet). The short wrench surfaces are designed so you can secure it properly but it still match the bolt head on the Stromberg banjo. When they?re all tightened up against the banjo, it looks like one solid piece. - Spaces banjo out one inch from fuel inlet - Instant clearance for 3x2 progressive linkage - Proven Stromberg superseat seal into S-jet - Short wrench surfaces match banjo bolt - Fits single and double banjos - Media polished stainless steel price: $11.95 |
 more detail Stromberg SuperSeat Hose Fitting NEW! From Stromberg, the folks who make the new 97 so you know it's good. Here's a 5/16" hose fitting with the correct 18 degree seat. The hex part is kept short for good looks, and so is the thread length - so it works as well with mystery aftermarket inlet fittings as with the Stromberg S-jet. price: $7.95 |  more detail CHROME Stromberg SuperSeat Hose Fitting NEW! Here's the same Stromberg SuperSeat Hose Fitting describe above with beautiful CHROME plating. price: $9.37 |
 Mini Hose Clamp Hose clamp are 100% stainless steel marine grade. These clamps are perfect to use with fuel fittings and fuel line. Size is 7/32" to 5/8" (5.6mm to 16mm) - 5/16" wide. |  more detail Stainless Steel Carburetor Throttle Arm This super nice Stainless Steel throttle arm is 1-7/8" long and an awesome 5/16" thick! Even the set screw is Stainless Steel! Fits a .274 shaft for use on Stromberg, Holley 94 and Edelbrock 94 carbs. Made in USA. price: $8.95 |
 Stromberg Rod End Stromberg rod ends come in right and left hand threads for easy adjustment. Just spin the rod to adjust for the correct lever angles. Stromberg rod ends require 10-32 threaded rod and 9/16th length of thread. |  more detail Stromberg SuperLink throttle arm NEW! The Stromberg SuperLink throttle arm is a totally new, high pressure die-cast zinc part that looks both modern and traditional at the same time. The modern H-beam section provides strength without extra weight, and the small reveal at the bottom edge adds to the period feel. The SuperLink arm works perfectly with the full range of new and original Stromberg carburetors - 97, 40, 48 and 81 and more - and also the Holley 94 with an extended shaft. It can be drilled out to fit oversize (0.281 inch) throttle shafts and to 5/16th inch to fit the popular Rochester 2G carburetors. (Priced Each) price: $10.95 |
 more detail Stromberg SuperLink throttle arm - with swivel NEW! The Stromberg SuperLink throttle arm is a totally new, high pressure die-cast zinc part that looks both modern and traditional at the same time. The modern H-beam section provides strength without extra weight, and the small reveal at the bottom edge adds to the period feel. The SuperLink arm works perfectly with the full range of new and original Stromberg carburetors - 97, 40, 48 and 81 and more - and also the Holley 94 with an extended shaft. It can be drilled out to fit oversize (0.281 inch) throttle shafts and to 5/16th inch to fit the popular Rochester 2G carburetors. (Priced Each). Swivel cross hole is sized for a 3/16" diameter linkage rod. price: $16.95 |  more detail Long throttle lever with swivel Designed to match the shorter Superlink lever arms, this longer version comes with a swivel and roll pin. Like its shorter partners, 9096K is also zinc die-cast with a modern H-beam section for high strength without excess weight. The countersunk stainless steel screw matches those on the carburetor and threads directly into the arm for serious grip. And the stainless steel swivel is secured by a small e-clip, with a 3/16th diameter cross hole for the linkage rod and a black knurled-tip set screw. There are three adjustment/connecting holes in this lever so you can move the swivel to change your linkage leverage and pedal/throttle response. - Modern H-beam section - Countersunk clamping screw with real grip! - Swivel and set screw included - 3/32 roll pin supplied so arm can be drilled and pinned if required - Three top adjustment/connecting holes price: $19.95 |
 more detail Cable Throttle Bracket - Mounts your hot rod cable throttle kit - Accepts hot rod auto-trans kickdown cable kits - Separate mount for traditional throttle return springs. - All stainless steel - Comes with new Stromberg carb-to-manifold gasket Securely mounted between the carburetor and intake manifold, our Cable Throttle Bracket positions the cable for optimum, bind-free pull on the Stromberg progressive linkage. Compatible with most readily available hot rod cable throttle kits (e.g. Lokar). A fixing hole is also provided for the small extension bracket supplied with most hot rod auto-trans kickdown cable kits. And a separate side arm provides a mount for a traditional return spring. Again, the 'Lokar' parts are recommended. While it was principally designed to work with small block Chevy and Ford applications, it is also compatible with most Ford Flathead tripower intake manifolds, (though not with the stock fuel pump). price: $40.95 |  more detail Long lever with kickdown capability - 9096K lever with additional auto-trans kickdown capability - 1/4-UNF thread takes a Lokar-style kickdown cable end - Countersunk clamping screw with real grip! - Swivel and set screw included - 3/32 roll pin supplied so arm can be drilled and pinned if required - Three top adjustment/connecting holes - Use in conjunction with Cable Throttle Bracket 9136K Our 9096K long lever with additional auto-trans kickdown capability - a 1/4"-UNF thread at the bottom end takes a Lokar-style kickdown cable end. Like its shorter partners, 9096K is also zinc die-cast with a modern H-beam section for high strength without excess weight. The countersunk stainless steel screw matches those on the carburetor and threads directly into the arm for serious grip. And the stainless steel swivel is secured by a small e-clip, with a 3/16th diameter cross hole for the linkage rod and a black knurled-tip set screw. There are three adjustment/connecting holes in this lever so you can move the swivel to change your linkage leverage and pedal/throttle response. Designed to be used in conjunction with our Cable Throttle Bracket (9136K), these arms are the foundation of all our 32 TwoStep progressive linkages (with kickdown), of course. We also include a 3/32 roll pin, so it can be drilled and pinned to the shaft for more positive location if required. price: $20.95 |
 more detail Snapback Return Spring New Stromberg Snapback throttle return springs wrap around the end of the throttle shaft of your new or original Stromberg 97, 81, or 48. These are black Stainless Steel torsion springs snap the carburetor shut. Price for two (2) springs. (Non black spring is shown for illustration). price: $10.95 |  Throttle Linkage Arm These aluminum throttle linkage arms come in two sizes. Choose arm to fit a 3/8" shaft or 5/16" shaft |
 more detail Carburetor Linkage Rod End Carburetor linkage rod end fits rods with a 1/4"-28 thread. (Each) price: $6.50 |  more detail Multi-hole arm Aluminum multiple hole carb arm - a big help while building your progressive multi carb linkage. Feature twin Allen head set screws. price: $17.95 |
 more detail Multi Hole Arm Here's another style of the useful multi hole arm for use when building thottle linkage set ups. Center fits .282" diameter shafts and is 4" long. price: $12.95 |  more detail Universal Bell Crank Kit Universal Bell Crank Kit comes complete with mounting bracket and works great for custom push or pull linkage applications. Feature include center 1/4" diameter hole and adjustable arms for various ratios and positions. Size is 7-1/4" height and 5-3/4" depth. price: $36.95 |
 more detail Stromberg Throttle Return Bracket This throttle return bracket fits on the Stromberg Carb at the bottom of the main carb body and features adjustable return spring. Great for single or multi-carb setups. Made in USA. price: $8.95 |  more detail Long Return Springs Here's some nice extra long throttle return springs that may be adjusted to different lengths to suit your needs. Price per pair. price: $7.95 |
 more detail Stainless Steel Dual Return Springs This universal stainless steel dual spring kit includes polished stainless steel mounting bracket and springs. price: $9.99 |  more detail Universal Return Spring Bracket Here's a nice chrome plated steel bracket that provides a convenient mounting location for return spring. price: $3.95 |
 more detail Linkage Swivel Linkage swivel with set screw used for building linkage for multi carb set ups. Works with 1/4" rods. price: $8.95 |  more detail Control Swivel Linkage with 360 degree swivel and set screw. Great for miss alignment linkage. Works with 1/4" rods. price: $5.95 |
 more detail Aluminum Collar Aluminum Collar with set screw helps when building or modifying your linkage. Works on 1/4" rod. price: $2.95 |  more detail Brass Fuel Inlet Repair Insert These brass inserts are used to repair the damaged or stripped fuel inlet threads on Stromberg 97/81/48 bodies. Use a 33/64 drill and 9/16-18 tap. Made in USA. (Priced each). price: $17.95 |
 more detail 6x2 Back-bar kit Back-bar linkage ONLY - use with two 3x2 Progressive kits for full 6x2 linkage: - Unique low-line brackets support the shaft at four points for zero flex and positive operation - Clamped and pinned levers ensure positive grip on the Back-bar, with 3-position adjustment for leverage and throttle response - Die-cast zinc SuperLink lever arms. All other parts stainless steel - Stainless end stops prevent lateral movement - Supplied pre-assembled. With instructions! This Trim-to-fit Back-bar Kit can be used on intakes with the following maximum dimensions: Carb spacing on each bank : 5-1/2 inches maximum Distance between the two banks: 9-1/8 inches maximum Offset how far one bank is in front of the other: 1 inch maximum. Trim-to-Fit kits are supplied with one long and one short Back-bar bracket. You leave the short one alone, and trim the long one to suit your own offset. Carburetors and manifold not included. This kit comprises only the following: - 2 stainless steel Back-bar brackets with rolled ends, Oilite self-lubricating bushes and two small washers to take up any height difference in the base castings. - 7mm stainless steel Back-bar shaft. - Two long levers, with swivels and clamping screws. One lever is pinned to the shaft. The other is drilled for a 3/32 roll pin (supplied) allowing you to position this lever to suit your intake width. - Two stainless steel end stops to prevent lateral movement in the Back-bar shaft. - Two stainless steel rods with swivels the links between the Back-bar levers and the primary carburetors. price: $130.95 |  more detail 6x2 Direct Linkage kit - Trim-to-Fit This Trim-to-fit Linkage kit can be used on intakes with the following maximum dimensions: - Carb spacing on each bank : 5-1/2 inches maximum - Distance between the two banks: 9-1/8 inches maximum - Offset how far one bank is in front of the other: 1 inch maximum. Trim-to-Fit kits are supplied with one long and one short Back-bar - bracket. You leave the short one alone, and trim the long one to suit your own offset. IMPORTANT NOTE: Our pictures show a full 6x2 linkage when assembled. Carburetors and manifold not included. This kit comprises the following: - Two stainless steel Back-bar brackets with rolled ends, Oilite self-lubricating bushes and two small washers to take up any height difference in the base castings. - Stainless steel Back-bar shaft with two stainless steel end stops to prevent lateral movement. - Two long levers, with swivels and clamping screws. One lever is pinned to the shaft. The other is drilled for a 3/32 roll pin (supplied) allowing you to position this lever to suit your intake width. - Two stainless steel links between the Back-bar levers and the center carburetors, with swivels and rod ends. - Six 9091K Superlink throttle levers with swivels - inc two special swivels to mount the rod ends - plus two long link rods. - Four Stromberg Snapback throttle return springs price: $240.95 |
 more detail 6x2 Back-bar kit - fits Edelbrock X1 This Back-bar ONLY kit fits the Edelbrock X1 ram 6x2 intake - Use with two Stromberg 9251PRO 3x2 TwoStep Progressive Linkage kits to build a full 6x2 progressive linkage. - This Back-bar Kit is supplied 'ready-to-fit' the Edelbrock X1 ram 6x2 intake. - Carb spacing on each bank : 4-7/8 inches - Distance between the two banks: 9-1/8 inches - Offset how far one bank is in front of the other: zero. IMPORTANT NOTE: Our pictures show the full 6x2 linkage when assembled. Carburetors and manifold not included. This kit comprises only the following: - 2 stainless steel Back-bar brackets with rolled ends, Oilite self-lubricating bushes and two small washers to take up any height difference in the base castings. - 7mm stainless steel Back-bar shaft. - Two long levers, with swivels and clamping screws. Both levers are pinned to the shaft. - Two stainless steel end stops to prevent lateral movement in the Back-bar shaft. - Two stainless steel rods with swivels the links between the Back-bar levers and the primary carburetors. price: $130.95 |  more detail 6x2 Direct Linkage kit - fits Edelbrock X1 This 6x2 Direct linkage kit fits the Edelbrock X1 ram 6x2 intake and comes as a complete linkage from Back-bar to carburetors, including return springs - Complete 6x2 non-progressive linkage from Back-bar to carburetors - CAD optimized function, plus great looks - Unique low-line brackets support the shaft at four points for zero flex and positive operation - Clamped and pinned levers ensure positive grip on the Back-bar, with 3-position adjustment for leverage and throttle response - Die-cast zinc SuperLink lever arms. All other parts stainless steel - Four Stromberg Snapback throttle return springs - Cool satin finish. Chrome available to special order - Supplied pre-assembled. With instructions! price: $240.95 |
 more detail Back-bar kit - fits Offy Pacesetter 3924 This Back-bar kit fits the Offenhauser Pacesetter 3924 6x2 intake - Use with two Stromberg 9253PRO 3x2 TwoStep Progressive Linkage kits to build a full 6x2 progressive linkage. -Back-bar linkage ONLY - use with two 9253PRO 3x2 Progressive kits for full 6x2 linkage - CAD optimized function, plus great looks - Unique low-line brackets support the shaft at four points for zero flex and positive operation - Clamped and pinned levers ensure positive grip on the Back-bar, with 3-position adjustment for leverage and throttle response - Die-cast zinc SuperLink lever arms. All other parts stainless steel - Stainless end stops prevent lateral movement - Cool satin finish. - Supplied pre-assembled. With instructions! price: $130.95 |  more detail 6x2 Direct Linkage kit - fits Offy Pacesetter 3924 This 6x2 Direct linkage kit fits the Offenhauser Pacesetter 3924 6x2 intake and comes as a complete linkage from Back-bar to carburetors, including return springs. - Complete 6x2 non-progressive linkage from Back-bar to carburetors - CAD optimized function, plus great looks - Unique low-line brackets support the shaft at four points for zero flex and positive operation - Clamped and pinned levers ensure positive grip on the Back-bar, with 3-position adjustment for leverage and throttle response - Die-cast zinc SuperLink lever arms. All other parts stainless steel - Four Stromberg Snapback throttle return springs - Cool satin finish. - Supplied pre-assembled. With instructions! price: $240.95 |
 more detail 4x2 Direct Linkage kit - Trim-to-Fit This Trim-to-Fit 4x2 Direct linkage kit adapts to a wide variety of applications and comes as a complete linkage from Back-bar to carburetors, including return springs. - Complete 4x2 non-progressive linkage from Back-bar to carburetors - CAD optimized function, plus great looks - Unique low-line brackets support the shaft at four points for zero flex and positive operation - Clamped and pinned levers ensure positive grip on the Back-bar, with 3-position adjustment for leverage and throttle response - Die-cast zinc SuperLink lever arms. All other parts stainless steel - Two Stromberg Snapback throttle return springs - Cool satin finish - Supplied pre-assembled. With instructions! price: $240.95 |  more detail 4x2 Direct Linkage kit - fits Offy Pacesetter 5024 This 4x2 Direct linkage kit fits the Offenhauser Pacesetter 5024 4x2 intake and comes as a complete linkage from Back-bar to carburetors, including return springs. - Complete 4x2 non-progressive linkage from Back-bar to carburetors - CAD optimized function, plus great looks - Unique low-line brackets support the shaft at four points for zero flex and positive operation - Clamped and pinned levers ensure positive grip on the Back-bar, with 3-position adjustment for leverage and throttle response - Die-cast zinc SuperLink lever arms. All other parts stainless steel - Two Stromberg Snapback throttle return springs - Cool satin finish - Supplied pre-assembled. With instructions! price: $240.95 |
 Genuine Stromberg 2x2 Linkage kit These new direct linkage kits are available as Swivel or Premium with left and right-hand threaded rod ends for easy adjustment. Choose Swivel or Premium and Flathead Ford intake size below. Check out these features: - Apart from the die-cast zinc SuperLink arms, all parts are Stainless Steel even the rod ends and lock nuts. - Every kit comes with two new Stromberg "Snapback" throttle return springs which wrap around the end of the throttle shaft. These black Stainless Steel torsion springs snap the carburetors shut. - Special swivels and matching rounded bolts were developed to clamp the rod ends tight, yet still allow the sliding swivel to rotate. The rounded bolt has a small blind hole in the head. Simply insert the same hex key you use for the grub screws and it stops the bolt turning when you tighten the lock nuts. The Premium 2x2 carburetor linkage features ball-bearing rod ends for positive action, Swivel linkage features Superlink levers - Flathead Intake Sizes: Offenhauser 2x2 Regular, Edelbrock 1103 2x2 Slingshot = 4-3/4" carb to carb Offenhauser 2x2 Super = 9-1/8" carb to carb Edelbrock 2x2 Super = 10-3/8" carb to carb |  more detail TwoStep Premium Linkage. 4-3/4in. CHROME Here's a Premium, CHROME 2x2 carburetor linkage with rod ends for positive action. Use with intake manifolds that put the carburetors 4-3/4 inches apart. Check out these features: -4-3/4 inches from carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits Offenhauser 1090 & 1075 2x2 Regular intakes -Fits Edelbrock 1103 2x2 Slingshot intake -Fits Navarro 2x2 Regular intake -Fits Eddie Meyer 2x2 High-rise intake -Fits Thickstun PM-7 High-rise intake -Works with all Stromberg 9141 TwoStep fuel lines price: $116.95 |
 more detail TwoStep Linkage. 4-3/4in spacing. CHROME Here's a competitively priced, CHROME 2x2 carburetor linkage with Superlink levers. Use with intake manifolds that put the carburetors 4-3/4 inches apart. Check out these features: -4-3/4 inches from carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits Offenhauser 1090 & 1075 2x2 Regular intakes -Fits Edelbrock 1103 2x2 Slingshot intake -Fits Navarro 2x2 Regular intake -Fits Eddie Meyer 2x2 High-rise intake -Fits Thickstun PM-7 High-rise intake -Works with all Stromberg 9141 TwoStep fuel lines price: $56.95 |  more detail TwoStep Premium Linkage. 9-1/8in. CHROME Here's a Premium, CHROME 2x2 Super carburetor linkage with rod ends for positive action. Use with intake manifolds that put the carburetors 9-1/8 inches apart. Check out these features: -9-1/8 inches from carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits Offenhauser 1071 & 1073 & 1076 2x2 Super intakes -Fits Navarro 2x2 Super intakes (Standard & Racing models) price: $121.95 |
 more detail TwoStep Linkage 9-1/8in. CHROME Here's a competitively priced, CHROME 2x2 Super carburetor linkage with Stromberg Superlink levers. Use with intake manifolds that put the carburetors 9-1/8 inches apart. Check out these features: -9-1/8 inches from carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits Offenhauser 1071 & 1073 & 1076 2x2 Super intakes -Fits Navarro 2x2 Super intakes (Standard & Racing models) price: $61.95 |  more detail TwoStep Premium Linkage 10-3/8in. CHROME Here's a Premium, CHROME 2x2 Super carburetor linkage with rod ends for positive action. Use with intake manifolds that put the carburetors 10-3/8 inches apart. Check out these features: -10-3/8 inch carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits Edelbrock 1100 2x2 Super intake price: $121.95 |
 more detail TwoStep Linkage 10-3/8in. CHROME Here's a competitively priced, CHROME 2x2 Super carburetor linkage with Stromberg Superlink levers. Use with intake manifolds that put the carburetors 10-3/8th inches apart. Check out these features: -10-3/8 inch carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits Edelbrock 1100 2x2 Super intake price: $61.95 |  more detail TwoStep Premium Linkage 5in. to 5-3/16in. CHROME Here's a Premium, CHROME 2x2 carburetor linkage with rod ends for positive action. This linkage is sized for use with intake manifolds and manifold adapters that space the carburetors 5 to 5-3/16in apart, including most '2x2 into 4-bbl' adapters, and the Vern Tardell Slingshot 2x2. Check out these features: -5 inches to 5-3/16 inches from carb to carb -Show chrome/polished stainless steel finish -Extended throttle shafts not required -Fits 4-cylinder Equalizer and Riley Two Port 2x2 intakes (5in) -Fits most 2x2 adapters designed for 4bbl carb intakes (5-3/16in) -Fits Vern Tardell Slingshot 2x2 adapter (5-3/16in) price: $116.95 |
 Genuine Stromberg 3x2 Linkage kit - Progressive These new linkage kits are available as Progressive kits with left and right-hand threaded rod ends for easy adjustment. (Swivel/straight 3x2 linkage opens all the carbs at once, progressive linkage opens the middle carb first). Choose Flathead Ford or small block Chevy intake size below. Check out these features: - Apart from the die-cast zinc SuperLink arms, all parts are Stainless Steel even the rod ends and lock nuts. - Every kit comes with two new Stromberg "Snapback" throttle return springs which wrap around the end of the throttle shaft. These black Stainless Steel torsion springs snap the carburetors shut. - Special swivels and matching rounded bolts were developed to clamp the rod ends tight, yet still allow the sliding swivel to rotate. The rounded bolt has a small blind hole in the head. Simply insert the same hex key you use for the grub screws and it stops the bolt turning when you tighten the lock nuts. |  Genuine Stromberg 3x2 Linkage kit Straight Swivel These new linkage kits Straight Swivel kits with left and right-hand threaded rod ends for easy adjustment. (Swivel/straight 3x2 linkage opens all the carbs at once, progressive linkage opens the middle carb first). Choose Flathead Ford or small block Chevy intake size below. Check out these features: - Apart from the die-cast zinc SuperLink arms, all parts are Stainless Steel even the rod ends and lock nuts. - Every kit comes with two new Stromberg "Snapback" throttle return springs which wrap around the end of the throttle shaft. These black Stainless Steel torsion springs snap the carburetors shut. - Special swivels and matching rounded bolts were developed to clamp the rod ends tight, yet still allow the sliding swivel to rotate. The rounded bolt has a small blind hole in the head. Simply insert the same hex key you use for the grub screws and it stops the bolt turning when you tighten the lock nuts. |
 more detail 3x2 Linkage Nice 3x2 Ball Bearing Progressive " Low Profile " Linkage. Works great on Ford Flatheads or low profile manifolds such as Chevrolet, early Olds and manifolds with carb bases close to the plane of the manifold. Fully progressive with ball bearing spherical end links for smooth operation. Aluminum rods and zinc plated pivots. for Stromberg and Holley carbs price: $69.95 |  more detail 2x2 Linkage 2x2 inline progressive ball bearing spherical end linkage with aluminum rods. price: $45.95 |
 Double Ends Carburetor Linkage Double end carburetor linkage features a 3/16" steel rod - choose from 3 lengths. * 3-1/2" - Ball hole center to center is adjustable from 4-1/2" to 5" * 7" - Ball hole center to center is adjustable from 7-1/2" to 8" * 9" - Ball hole center to center is adjustable from 9-1/2" to 10" |  more detail Single End Carburetor linkage Here's a 3/16" steel rod carburetor linkage with a single end. Perfect for your Stromberg 97 Carburetor. price: $10.95 |
 more detail Throttle Ball Assortment Many applications use a ball on the carburetor arm to hook the linkage to. Includes 4 throttle balls with various threads. price: $14.95 |  more detail Choke Cable 6' w/ Black Knob Here's a nice six foot long choke cable with Black push/pull knob. May be cut to length and requires a 3/8 diameter mounting hole. price: $11.50 |
 more detail Stainless Steel Throttle Cable Here's very nice universal Stainless Steel throttle cable perfect for your hot rod or custom. Cable is 24" long and may be cut to length. Aluminum fittings and an aluminum ferrule to eliminate fraying. Designed to work with any aftermarket single carburetor, multiple carburetor set up or dual carb supercharger. price: $38.95 |  more detail Carburetor Adapter Bolt a newer type 4-bolt carb (3-1/4" x 1-7/8", like Rochester 2GC) to an early 3-bolt manifold. Or, turn it upside down and bolt a Stromberg 97 or Holley 94 to a 4-bolt carb manifold. Aluminum casting and 1-1/2" tall. price: $27.95 |
 more detail Vintage 3-Bolt Carburator Adapter This 2X2 to 4 barrel carburator adapter allows you to mount any Stromberg 97, 81 or 48 or Holley "94" three bolt carb to the small 4v (WCFB) Carter AFB or the Holley 4 barrel carb intake and includes mounting bolts and two 3-bolt carb mounting gaskets. - Spacing for two barrel carbs is 5-1/4" center to center - Thickness is 1-5/8" price: $97.95 |  more detail Phenolic Carb Spacer This 1/4" thick phenolic spacer fit common 3-bolt base Stromberg, Holley and Ford carbs. price: $25.95 |
 more detail Stromberg 97 Premium Service Kit Premium Service Kit for 97 / 40 / 48 - the best available! - 3 x Stromseal 'no leak' main gaskets - 5 x (2 spares) bowl plug gaskets - Power jet gasket - S-jet 'twin-ball' inlet valve with gasket - Accelerator pump check valve - 2 x idle mixture screws and springs - Full accelerator pump assembly with new springs, washers, retainer, felt - even the cotter pin - Stainless steel float gauge - Detailed installation instructions price: $45.95 |  more detail Full gasket kit Full gasket kit - three main gaskets (non-paper), plus felt gasket for accelerator pump, and ring gaskets for power jet, inlet valve and drain plugs price: $10.95 |
 more detail Blank-Off Plate Stainless steel and cut to the late 97 base shape and a millimetre smaller than the official gasket size. Fit the plate BETWEEN the gasket and carburtor - NOT under the gasket price: $13.95 |  more detail Aluminum Block-Off Plate Finned Aluminum Block-Off Plate for 3-bolt carburetor price: $15.95 |
 more detail Adjustable Main Jets for Stromberg These adjustable main jets are machined to high standards on Swiss screw machine. Part has a stainless steel needle and brass body and nut with Viton O-ring seal. Simply remove your jet well plugs and screw in this adjustable jet assembly. Use the largest stock jet size for the richest mixture you need, then use the adjuster to lean it down from there. You can lean your mixture by turning clockwise or rich by turning counter clockwise. Includes Teflon sealing washer, extra O-ring seals & instructions. Fits Stromberg 48, 81, and 97 carburetors. Sold per PAIR. price: $55.95 |  Genuine Stromberg Main Jets Main Jets are sold two per package - enough for one Stromberg carburetor. All sizes available. Note: 0.045 are stock size jets for Stromberg 97. |
 more detail Stromberg Premium Jet Wrench From Stromberg! Not just any old wrench, but a super cool stainless steel version with neat straight knurls on the end for good grip and control, and a CNC milled end for a super fit on the jet itself. price: $29.95 |  more detail Stromberg Jet Wrench Stromberg Jet Wrench - just what you need to change your new jets! price: $17.95 |
 more detail Accelerator pump rod - Stromberg 97, 81 For Stromberg 97 & 81 Accelerator pump rod for 97 and 81 - stainless steel price: $19.95 |  more detail Accelerator pump rod - Stromberg 40, 48 For Stromberg 40 & 48 Accelerator pump rod for 40 and 48 - stainless steel price: $19.95 |
 more detail Bowl gallery plugs Bowl gallery plugs (pack of 20) price: $9.95 |  more detail Bowl plug kit Bowl plug kit - all 3 plugs with gaskets price: $19.95 |
 more detail Bowl plug gaskets Bowl plug gaskets (pack of 10) price: $4.95 |  more detail Accelerator Pump Lever Accelerator pump lever, spring & cotter pin - stainless steel price: $19.95 |
 more detail Kicker Assembly Stainless steal kicker assembly including choke lever, idle screw & end stud price: $35.95 |  more detail Kicker Assembly/cable choke Stainless steal kicker assembly including choke lever, idle screw, cable choke plate & end stud. Designed for '49 and later Fords. The included separate bracket mounts off the rear body screw to hold the choke cable price: $49.95 |
 more detail Cable Choke Bracket Here is the often requested Stainless Steel choke bracket that mounts off the rear body screw to hold the choke cable. For Stromberg 97, 81 or 48. price: $22.95 |  more detail Throttle shaft and lever kit Throttle shaft and stainless steal lever kit including screws & bushes - stock size. Bushings need to be reamed with .278 reamer. price: $36.95 |
 more detail Lincoln Zephyr Throttle shaft and lever kit This is the new Lincoln Zephyr Throttle shaft and stainless steal lever kit for your Stromberg 97, 81, or 48. It's designed to push instead of pull the throttle lever. This is handy for cars like the 1949 Mercury or any 1930s Lincoln Zephyr where the pedal does exactly that. This part is a replica of the original Lincoln Zephyr part. Bushings need to be reamed with .278 reamer. price: $39.95 |  more detail Chucking Reamer .278 The correct reamer for your new Stromberg throttle shaft. Made of high-speed steel chucking reamer .2780" Dia, 1-1/2" long flutes, 6" overall length with 6 flutes. price: $29.95 |
 more detail Stromberg 97 Extended Throttle Shaft - .282" size New extended throttle shaft is .282" diameter which is .005" oversize. To install use a 9/32" drill bit or reamer through the base plate. Throttle plate screws included with shaft. The shaft is 1/2" longer than the stock throttle shaft. price: $17.95 |  more detail Throttle plates Throttle plate with the correct 7 degree edge - sold by the pair price: $13.95 |
 more detail Idle adjusting screws Idle adjusting screws with springs - sold by the pair price: $12.95 |  more detail Fuel inlet Fuel inlet Jet with gasket price: $16.95 |
 more detail Idle Jets Idle jets - sold by the pair price: $16.95 |  more detail Stromberg Float NEW! The new all brass Genuine Stromberg float you have been waiting for! Perfect for your Stromberg 97 or Stromberg 81 (or 48). This is an exact reproduction and faithful to the original Ford drawings. Includes new Stromberg hinge pin #9558K. price: $23.95 |
 more detail Float pin New Stromberg float hinge pin price: $5.95 |  more detail Emulsion tubes Emulsion tubes - pair price: $22.95 |
 more detail Choke lever detent plunger Choke lever detent plunger & spring - stainless steel price: $5.95 |  more detail Choke Lock Detent Pin Don't use your choke? Then this choke lock detent pin is for you. Most Strombergs even in multiples - run better with the choke plates in. But who needs rattling levers? Lock them open with this clever detent plunger install into the airhorn as per the stock item, but press the pin end into your choke lever. Stainless Steel. price: $6.95 |
 more detail Choke shaft kit Choke shaft kit including lever, washer, screw & end stud price: $18.95 |  more detail Choke plate kit Choke plate kit including screws - stainless steel plate price: $12.95 |
 more detail Accelerator pump check valve Accelerator pump check valve price: $5.95 |  more detail Accelerator pump discharge jet Accelerator pump discharge jet plus collar - per pair price: $19.95 |
 more detail Throttle/choke plate screw kit Throttle/choke plate screw kit - pack of 10 price: $5.95 |  more detail Throttle stop screw & spring Throttle stop screw & spring - stainless steel price: $5.95 |
 more detail Choke & accelerator pump lever fulcrum screws Choke & accelerator pump lever fulcrum screws price: $11.95 |  more detail Body screw kit Body screw kit - 8 screws/washers - stainless steel price: $10.95 |
 Power by-pass jet with gasket Size 65 is stock Stromberg 97 Power by-pass jet size. |  more detail Accelerator pump Accelerator pump - stainless steel rod price: $9.95 |
 more detail Accelerator pump kit - 97/48/40 Accelerator pump kit including springs/retainers/washers/felt gasket/cotter pin - for Stromberg 97/48/40. (Stormberg 81 is a different size). price: $19.95 |  more detail Spring kit Spring kit - all exterior springs - all stainless except idle adjuster springs price: $18.95 |
 more detail Manifold Gasket 6-pack Package of 6 manifold gaskets price: $11.95 |  Manifold Stud Kit & High Crown Nuts Complete your carburetor(s) set up with these great Stainless Steel high crown acorn nuts and stud kit. These kits include three or four studs, washers and Stainless Steel high crown acorn nuts. Choose three or four stud kit. |
 more detail 3 Manifold Stud Kit & Hardware 3 pack of manifold studs includes nuts and washers. price: $12.95 |  more detail 4 Manifold Stud Kit & Hardware 4 pack of manifold studs includes nuts and washers. price: $16.95 |
 more detail Stromberg 81 Premium Rebuild Kit NEW! Premium Service Kit for Stromberg 81 - Full gasket kit, No-stick S-jet inlet valve, Accelerator pump check valve, 2 idle mixture screws and springs, full 81-size accelerator pump kit, installation sheet and float gauge. These are proper kits with the correct LEATHER seal and an exact replica of the wacky little brass spider that goes under the leather. The big spring retainer is turned aluminum with a tiny E-clip to hold it all in place. price: $49.95 |  more detail Stromberg 81 accelerator pump NEW! Accelerator pump for the Stromberg 81. What a beauty - with correct 10-finger brass spring washer beneath a leather seal. price: $15.95 |
 more detail Stromberg 81 accelerator pump - full kit NEW! Accelerator pump kit for the Stromberg 81. Talk about original. Our 81 pump has a correct 10-finger brass spring washer beneath a leather seal. Kit includes two springs/retainer/washers/felt gasket even a cotter pin price: $25.95 |  more detail Y-Block Fuel Block - Polished Polished aluminum Muroc Fuel Distribution Block has a 5/16" inlet line, and two outlets. Features countersunk mounting holes and polished finish. price: $30.95 |
 more detail Y-Block Fuel Block - Cast Cast finish aluminum Muroc Fuel Distribution Block has a 5/16" inlet line, and two outlets. Features countersunk mounting holes and as cast finish. price: $26.95 |  Polished Muroc Fuel Block These Muroc fuel blocks feature a fine polish, 5/16" inlet line and countersunk mounting holes. Choose the number of outlets below. 4 Carb block is 7" wide 3 Carb block is 5-1/2" wide 2 Carb black is 4" |
 Cast Finish Muroc Fuel Block These Muroc fuel blocks feature a cast finish, 5/16" inlet line and countersunk mounting holes. Choose the number of outlets below. 4 Carb block is 7" wide 3 Carb block is 5-1/2" wide 2 Carb black is 4" |  more detail Edelbrock Mini Fuel Block The Edelbrock Mini Fuel Block was first introduced in the late 1950's and it's a great solution for any dual or triple carb application where no mounting surface is available. It features a single 1/4" inlet with three 1/4" outlets. Comes with a polished finish and period correct Edelbrock logo. May be used with any dual carb by blocking off the unused outlet with 1/4-18" NPT plug. Also, the third outlet can run a fuel pressure gauge. Made in USA. price: $63.95 |
 Fuel Block 3-Port This old school design has been refined into a better product, visually and mechanically. This quality aluminum casting features 3 outlet ports, inlet and outlet drilled and tapped for standard 5/16" NPT gas line fittings. Run multiple carbs, or add a fuel pressure gauge. Sturdy mounting tabs ensure a secure installation. Mounts to any flat surface. Made in USA. |  2 Port Finned Fuel Log Here is the new OTB Gear fuel log design - available in 2,3, or 4 port versions. Use all ports to feed carburetors, or dedicate one for a fuel pressure gauge. Cast in quality aluminum alloy, and provided in your choice of polished or unpolished finishes. Inlet and outlet drilled and tapped for standard 5/16" NPT gas line fittings. Features 4 sturdy mounting tabs for #10 hardware. Length: 3-1/2". Made in USA. |
 3 Port Finned Fuel Log Here is the new OTB Gear fuel log design - available in 2,3, or 4 port versions. Use all ports to feed carburetors, or dedicate one for a fuel pressure gauge. Cast in quality aluminum alloy, and provided in your choice of polished or unpolished finishes. Inlet and outlet drilled and tapped for standard 5/16" NPT gas line fittings. Features 4 sturdy mounting tabs for #10 hardware. Length: 3-1/2". Made in USA. |  4 Port Finned Fuel Log Here is the new OTB Gear fuel log design - available in 2,3, or 4 port versions. Use all ports to feed carburetors, or dedicate one for a fuel pressure gauge. Cast in quality aluminum alloy, and provided in your choice of polished or unpolished finishes. Inlet and outlet drilled and tapped for standard 5/16" NPT gas line fittings. Features 4 sturdy mounting tabs for #10 hardware. Length: 3-1/2". Made in USA. |
 MOON FUEL BLOCK Dean Moon's original product which he made in High school - talk about traditional! Block features 3/8" npt inlet on both ends and 1/8" npt outlets. Polished aluminum and measures 6" x 2" x 1.25". |  more detail Y-Fuel Block The "Y" fuel block kit allows equal flow for multiple carburetors applications. It is manufactured from top quality aluminum with a 1/8" pipe thread hole cast into each unit to allow the use of a fuel pressure gauge at the "Y." Inlet and outlet openings are 3/8" NPT. Brass fuel line fittings, worm-drive clamps, and mounting screws are included. price: $25.95 |
 more detail "Offy" Style Fuel Block This fuel log has large 3/8" NPT inlet and outlets, equalize fuel flow to any multiple carburetor application. Polished aluminum and measures 4-3/4" x 2-3/4". price: $51.95 |  T-Style Fuel Block Chrome plated 4" long fuel block for multiple carburetor applications. Precision die cast and features 3/8" NPT inlet and 1/4" NPT outlets. Choose 4,3 or 2 outlet units. |
 more detail Electric Fuel Pump High flow, low pressure electric fuel pump equipped with a 5/16" inlet and outlet. The pump flows 18 gph at 4.0 psi, 5.5 psi maximum. may be regulated to 2-1/2 to 3 psi with external regulator. Includes a rubber padded mounting bracket and two heavy duty hose clamps. Rated 12 volt, 5 amp. Measures 4-1/2" long x 1-3/4" wide. Works great with your Stromberg 97s or CG 94s and the Holley fuel pressure regulator. Use the Fuel Pump Relay Kit to prevent voltage drops and maintain constant fuel pressure. price: $106.95 |  more detail Carter electric fuel pump The world famous Carter P4070 12 volt electric fuel pump features a rotary vane and a 72 gph flow rate. Inlet and outlet size is 1/4 in. NPT and maximum pressure 6 psi. Comes complete with mounting bracket and rubber isolation bushings. Works great with your Stromberg 97s or CG 94s and the Holley fuel pressure regulator. Use the Fuel Pump Relay Kit to prevent voltage drops and maintain constant fuel pressure. price: $102.95 |
 more detail Carter 6-Volt Fuel Pump Rotary vane design! Originally created for military use, this design has been in production longer than any other Carter model. Works with positive or negative ground 6-volt systems. Features 72 gph at 6 psi and 1/4" NPT inlet and outlet. Includes mounting hardware and bracket. price: $125.95 |  more detail Universal Fuel Pump Relay Kit A relay will prevent voltage drops at the pump thus maintaining constant fuel pump pressure, and will prevent fuel pump amperage from damaging the electrical system. Its a good idea to relay your fuel pump for the street and a must when you're racing. price: $38.95 |
 Chrome Fuel Filter Hi-Flow Chrome canister-type filter has 3/8" NPT inlet and outlet and is able to flow 90 gallons per hour. Comes complete with chrome bracket and mounting bolts. Features a replaceable 10 micron element. |  Chrome & Glass Fuel Filter Chrome housing ends with a clear glass center. Choose 5/16" or 3/8" fuel line. (Not for fuel injection). Visually inspect the condition of fuel and element. Uses a standard replacement filter element BEP11055 |
 Chrome OEM Style Fuel Filter Check out these features: - Designed to filter out harmful particles and debris form entering the carburetor - Factory style universal fit (not for fuel injection). - Chrome plated steel - Place between fuel pump and carburetor using fuel hose. - Choose 5/16" or 3/8" hose size |  Finned Fuel Filter A good looking, high quality solution for your fuel filter needs. Compact in size, considering it's large filtration capability. Precision machined of cast aircraft grade A-356 aluminum, and embellished with our graceful fins. We furnish a U.S. made filter - replacements available in your local market. Offered in highly polished or unpolished variations. Mounting hardware and gas line fittings are not included. Made in USA - The unpolished version is bead blasted for a smooth, uniform finish. - Drilled for 5/16" mounting bolts - holes are 4-3/16" center to center. - Drilled and tapped for 3/8" gas line fittings. - Max. width 5-1/4". - Projection from mounting surface 3-3/4". - Height with filter 4-3/4". - Filter provided has a max flow rate of 7-9 gallons per minute and a burst pressure of 255 PSI. - Comes complete with NAPA Gold filter #3386 |
 more detail Fuel Pressure Regulator This fuel pressure regulator from Mr. Gasket adjusts your fuel pressure on carburetor engines from 1 to 6 lbs. They fit 5/16" and 3/8" fuel line and include fittings, hose, and clamps. Perfect for your Stromberg or Holley, Edelbrock 94. price: $29.95 |  Premium Fuel Line Premium fuel line is reinforced to help prevent kinking and is rated up to 50 PSI for use with carbureted applications. Fuel line has many other uses including connecting PCV valves, coolant overflow tanks and for use as vent lines for transmissions and differentials. Line is compatible with gasoline, E-85, diesel and bio-diesel. Size indicated is I.D. of hose. |
 Red Braided See Through Fuel Line This Red Braided See Through Fuel Line is reinforced with an internal braid. This specially-formulated flexible tubing comes in 6 foot length. You can easily trim it to your needs. Works with normal slip-on hose barb fittings and clamps. Choose 3/8" or 5/16". |  Red See-Through Fuel Line Our Red See-Through Fuel Line is the perfect old-time accent to your multi-carb street rod! This specially-formulated, flexible tubing has a 3/8" or 5/16" inside diameter and comes in 6 foot length. You can easily trim it to your needs. Works with normal slip-on hose barb fittings and clamps. |
 more detail Continental Type Air Cleaner Continental Style 2 BBL and 4 BBL Air Cleaners Back in the 1950's Frank Dominianni was running his Hi-Speed Power Equipment speed shop in Valley Stream, NY. He was heavily involved with sports car racing and with the American importer of Ferrari automobiles (Luigi Chinetti). He also was a major importer of the Italmeccanica blower. He tooled up for and manufactured two and four barrel air cleaners which he called Continental Type. By far the most famous car that used these air cleaners was the 1932 Ford 3-window coupe show rod of Andy Kassa from New Jersey. O'Brien Truckers has created brand new patterns and core boxes to recreate these two air cleaners and manufacture them here in the USA. In addition, we commissioned two custom made cotton gauze washable lifetime elements which we wrap with screen and wire mesh to give our customers an air cleaner that not only looks like Frank's original Continental Type air cleaner but filters to modern day standards. Fits carbs with a 2-5/8" neck and is 16- 3/4" wide, 4-3/4" tall from the carb neck to the top. price: $248.95 |  more detail Edmunds Custom Air Cleaner Priced each. Edmunds Custom 4-1/2" tall polished aluminum round air cleaner. Fits carbs with 2-5/8" neck - includes traditional wire-mesh element. Made in USA. price: $68.95 |
 more detail Boetter Style "Bullet" Air Cleaner Here's a Boettger '53-'54 Corvette style air cleaner, but sized to fit 2-5/8" Stromberg and Holley style carbs. Air cleaner is 4" tall, 2-3/4" outside diameter, and fits 2-5/8" corroborator necks and secured with a set screw. Polished stainless steel and priced each. price: $90.95 |  more detail Bug Horn A perfect air cleaner for your Stromberg, Holley, & Ford 2 barrel carbs. Precision machined of premium aluminum alloy to fit solidly - secured with a stainless set screw. Each comes with our all stainless mesh Bug Dome to keep the big stuff out of your carb. The Bug Horn stands only 2" tall, for low hood clearance considerations. price: $59.95 |
 more detail Aluminum Skull Air Scoop Aluminum Skull Air Scoop - super quality with great polished finish. Designed to fit carburetors with 2-5/8" top like Stromberg 97 or Holley 94. ( Set screws not included - priced each ) price: $58.95 |  more detail Round Air Cleaner - Smooth Top Polished aluminum round 2" tall x 4" round air cleaner with lifetime element and smooth top. Fits Stromberg 97 / 81 / 48 or Holly / CG 94 carburetors with 2 5/8" top. Made in USA. (carb not included) price: $49.95 |
 more detail Round Air Cleaner Here's a classic polished finned aluminum round 2" tall x 4" round air cleaner. Fits Stromberg 97 / 81 / 48 or Edelbrock, Holly / CG 94 carburetors with 2 5/8" top. price: $46.95 |  more detail Air Scoop Famous "Frog Mouth" scoop. Polished aluminum casting with locking screw - fits carbs with 2-5/8" neck like Stromberg 97 or Holley / CG 94. Overall height is 4" and includes a set screw. price: $25.95 |
 more detail Hot Rod Frog Mouth Scoop Chrome plated - fits carburetors with 2 5/8" neck like 97s or 94s. These are heavier and chrome plated compared to the polished aluminum air scoops. Priced each. price: $25.95 |  more detail "Max Wedge" Polished Finned Aluminum Air Cleaner Wedge air cleaner fits carburetors with 2-5/8" neck. Features super nice polish and cast aluminum base. Top measures 6" wide x 3-1/4" tall x 4-1/2" front to back. Includes paper 4" filter. price: $98.95 |
 more detail Helmet Air Cleaner Measures 4" across the base. Helmet air cleaner fits all carburetors with a 2-5/8" neck. Chrome plated steel. Includes paper air cleaner 3-7/8" filter. price: $35.95 |  more detail Velocity Stack Velocity Stack has a polished stainless steel housing with locking screw. Features the timeless 1950's styling and fits all carburetors with a 2-5/8" diameter neck and 5" tall at the highest point. It is compact enough for all muli-carb setups and is beautifully polished. price: $25.95 |
 more detail "Muroc" Velocity Stack - 5-1/2" NEW! The Muroc velocity stack is 5-1/2" tall, cast aluminum, formed screen, and feature a fine polish finish. Designed for carburetors with 2-5/8" necks such as Stromberg 97s, 48s, 81s and Holley 94s. price: $66.95 |  more detail "Muroc" Velocity Stack - 7-1/2" NEW! The "Muroc" velocity stack is 7-1/2" tall, cast aluminum, formed screen, and feature a fine polish finish. Designed for carburetors with 2-5/8" necks such as Stromberg 97s, 48s, 81s and Holley 94s. price: $73.95 |
 more detail "Muroc" Velocity Stack - 9" NEW! The "Muroc" velocity stack is 9" tall, cast aluminum, formed screen, and feature a fine polish finish. Designed for carburetors with 2-5/8" necks such as Stromberg 97s, 48s, 81s and Holley 94s. price: $78.95 |  Flat Top 2 Barrel Air Cleaner Fresh retro mechanical design, set off with a solid brass badge and stainless rivets. Fits 2-5/8" diameter carburetors. Featuring our exclusive new Platinum Series filter in the low profile 2" height. This is the filter that "sparkles" in the sunlight. The fittings are cast from premium aircraft grade aluminum, which takes a higher than normal shine. All visible surfaces are polished - others may only polish the raised areas. The base casting is precision bored, with an internal shoulder to snugly fit your carburetor - not simply "cast to fit" as others may do. Our internal shoulder also keeps the cleaner from rocking around. Compare our features, we come out shining. Fits type 94,97, and 98 carbs, securing with a stainless socket set screw. Made in USA |
 Finned Air Cleaner Classical finned design, accentuated by "doming" the top for more definition. Fits 2-5/8" Diameter carburetors. Featuring our exclusive new Platinum Series filter. This is the filter that "sparkles" in the sunlight. The fittings are cast from premium aircraft grade aluminum, which takes a higher than normal shine. All visible surfaces are polished - others may only polish the raised areas. The base casting is precision bored, with an internal shoulder to snugly fit your carburetor. Choose polished or unpolished and 2" tall filter or 3-1/4" filter. Made in USA. |  Dome Air Cleaner Great retro design - reminiscent of baby hub caps. Fits 2-5/8" diameter carburetors. Featuring our exclusive new Platinum Series filter in the low profile 2" height - this is the filter that "sparkles" in the sunlight. The fittings are cast from premium aircraft grade aluminum, which takes a higher than normal shine. All visible surfaces are polished - others may only polish the raised areas. The base casting is precision bored, with an internal shoulder to snugly fit your carburetor - not simply "cast to fit" as others may do. Our internal shoulder also keeps the cleaner from rocking around. Made in USA. Fits type 94,97, and 98 carbs, secured with a stainless socket set screw. |
 more detail Spark Arrester Air Cleaner After 50 years out of production we have a new and improved "Spark Arrester" style air cleaner. Includes a custom cotton gauze lifetime element and fits carburetors with a 2-5/8" neck like Stromberg 97 and Holley 94. Made in USA. Priced each. price: $95.95 |  Mini Mohawk Air Cleaner The Mini Mohawk 2 Barrel Air Cleaner is cast from A-356 aircraft grade alloy and finished to show standards. Each comes with our 2"X4" Platinum Series filter for practicality and appearance. All visible surfaces are polished - others may only polish the raised areas. The base casting is precision bored, with an internal shoulder to snugly fit your carburetor - not simply "cast to fit" as others may do. Our internal shoulder also keeps the cleaner from rocking around. Choose polished or unpolished. |
 more detail Scoop Style Air Filter These air filters are designed to fit on top of 97/94 style carbs when fitted with air scoops or other air cleaners. (Fits 2-5/8" carb tops). Filters feature a washable foam element with steel mesh backing. price: $15.95 |  more detail Bug Dome New Stainless Steel "Bug Dome". Bug Domes will keep the big pieces out of your 2 barrel carburetors. Perfect for your traditional carburetors like Stromberg 97, 81 or 48 and Edelbrock / Holley 94. Since they fit within the I.D. of the carb throat, you can use them with popular slip over accessories such velocity tubes. Made in USA. price: $14.95 |
 more detail 2x4 Platinum Series Air Filter The OBT filter media is a medium gray, washable oiled cloth. Color wise, it blends with everything in the engine compartment. We specified stainless steel mesh instead of the normal black painted steel mesh to hold it together. The stainless adds a lot of sparkle to what is normally a pretty mundane looking item. Next, we required our supplier to mold the rubber ends very cleanly. Have you ever noticed how irregular and sloppy some brands are in this area. 2" high x 4" wide. The end result is a filter we can each be proud of, and that will look great for many years. Made in USA. price: $20.95 |  more detail 3.25x4 Platinum Series Air Filter The OBT filter media is a medium gray, washable oiled cloth. Color wise, it blends with everything in the engine compartment. We specified stainless steel mesh instead of the normal black painted steel mesh to hold it together. The stainless adds a lot of sparkle to what is normally a pretty mundane looking item. Next, we required our supplier to mold the rubber ends very cleanly. Have you ever noticed how irregular and sloppy some brands are in this area. 3-1/4" high x 4" wide. The end result is a filter we can each be proud of, and that will look great for many years. Made in USA. price: $24.95 On Sale! - $23.70 |
 more detail Washable Air Filter * 3-7/8" outside diameter * 2-3/4" inside diameter * 2-1/4" tall price: $11.25 |  more detail Genuine Stromberg License Plate Frame New from Genuine Stromberg is this great chrome metal license plate frame. price: $13.95 |
 more detail Stromberg Thermometer The Stromberg 24 gauge American steel thermometer measures 17" high and 5" wide. Made in USA. price: $31.95 |  more detail STROMBERG stickers - Outside Here's a page of STROMBERG stickers, 12 in all - these stick on the outside of glass or what ever you want to stick them on. price: $4.95 |
 more detail STROMBERG stickers - Inside Here's a page of STROMBERG stickers, 12 in all - these stick on the inside of glass. price: $4.95 |  more detail Stromberg Circle Metal Sign Patinated vintage style artwork with one riveted fixing hole at top. Size: 14" diameter. price: $25.95 |
 more detail Black Diamond Logo Metal Sign Patinated vintage style artwork and riveted fixing holes at four corners. Size: 28" wide. price: $30.95 |  more detail Stromberg Carburetors T-Shirt High quality Gildan black t-shirt with cream print. The Bendix Stromberg 97 Carburetor - nothing more traditional than that! Pure and simple. "Distressed" logo and carb design printed on front only. price: $20.00 (XXL - $22.00) |
 more detail Stromberg Racing Division T-shirt NEW! From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Black t-shirt with Stromberg Racing Division on front only. Made in USA. price: $22.95 (XXL - $24.95) |  more detail Stromberg script Black T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Black t-shirt with Stromberg script logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |
 more detail Stromberg script Grey T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Grey t-shirt with Stromberg script logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |  more detail Stromberg Script White T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. White t-shirt with Stromberg script logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |
 more detail Stromberg Circle Sign T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Cream t-shirt with Stromberg Circle Sign on front only. Made in USA. price: $22.95 (XXL - $24.95) |  more detail Stromberg Black Diamond Logo Black T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Black t-shirt with Stromberg Black Diamond Logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |
 more detail Stromberg Black Diamond Logo Grey T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Grey t-shirt with Stromberg Black Diamond logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |  more detail Stromberg Orange Diamond Logo Black T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. Black t-shirt with Stromberg Orange Diamond logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |
 more detail Stromberg Orange Diamond Logo White T-shirt From Genuine Stromberg. High quality, soft, 100% combed cotton T-Shirt from American Apparel, made in Downtown LA (as it says on the label) and screen printed nearby. White t-shirt with Stromberg Orange Diamond logo on front only. Made in USA. price: $22.95 (XXL - $24.95) |  more detail Orange diamond logo Cap Patch on front. Printed Stromberg Patents logo on back of hat. price: $22.95 |
 more detail Black triangle logo Cap Patch on front. Printed Stromberg Patents logo on back of hat. price: $22.95 |  more detail Yellow triangle logo Cap price: $22.95 |
 more detail Stromberg Orange diamond logo BEANIE From Genuine Stromberg. Stromberg Orange diamond logo black Beanie price: $14.95 |  more detail Stromberg Black triangle logo BEANIE From Genuine Stromberg. Stromberg Black triangle logo black Beanie price: $14.95 |
 more detail "Uni-Syn" Multiple Carb Balancing Tool If you have more than one carb on your Hot Rod, you need one of these "Uni-Syn" carb synchronizing tools. Just set on the top of your carb and adjust until all the carbs read the same. Works well on Stromberg 97, Holley and Edelbrock 94 and small one and two barrel carbs. price: $32.95 |  more detail MOON Fuel Pressure Gauge 0-15 MOON direct mount fuel pressure gauge measures 1-15 lbs. Liquid filled and 1-3/4" diameter with 1/8 NPT mount. price: $38.95 |
 more detail MOON Oil / Fuel Pressure Gauge 0 - 100 MOON direct mount fuel and/or oil pressure gauge measures 0-100 lbs. Liquid filled and 1-3/4" diameter with 1/8 NPT mount. price: $38.95 |  more detail Fuel Pressure Gauge 0-15 with engine turned face Direct mount fuel pressure gauge measures 1-15 lbs. Liquid filled with engine turned face and is 1-3/4" diameter with 1/8 NPT mount. price: $35.95 |
 Slingshot Intake Manifold Retro flathead style intake manifold. Converts any 2 barrel, 3 bolt style manifold to mount 2 carburetors. This sought after design, is cast in high quality aluminum and prized for its distinctive looks and performance enhancement characteristics. The Slingshot mounts the carburetors side by side so that they get equal air flow. Add a new level of sophistication to your engine. Dimensions: 9-1/2" long by 3-1/2" high. Made in USA. |  more detail Stromberg 97 Carburetors From Vern Tardel and friends. The seventh Let Me Help You guide for traditional Ford hot rod builders. This comprehensive 40-page booklet, Stromberg 97 Carburetor Service and Repair, illustrates and describes the disassembly, restoration, reassembly, and calibration of the classic Stromberg 97 carburetor. This step-by-step guide also provides an excellent overview for the repair of used Strombergs, and the required calibration and assembly techniques to make a Stromberg perform like new. price: $11.95 |
 more detail AIR CLEANER "SPIN NUT" Tri-Bar Spin Nut The Tri-Bar Spin Nut is chrome-plated for lasting beauty that enhances any air cleaner. Fits all 1/4 - 20 and 5/16-18 studs. price: $5.95 |
|
